TRIBORD
Ref.
8545930
2696266
SAILING 900 waterproof hat - Black
€21.00
Tax included
Store Availability
Store Availability
Our designer sailors have designed this waterproof hat for regular sailing in rainy weather.
BENEFITS
Weight
This hat weighs around 100 gramsWaterproof
Approved under simulated heavy rain (100L/m²/h) for 3h.Stability
Adjustment strap under the chinBreathability
3 -ply breathable laminated fabric (RET < 15)TECHNICAL INFORMATIONS
Waterproofing 1/2
We measure the resistance of a fabric to water pressure in mm of water column (based on the ISO 811 standard). The higher the water pressure withstood by the fabric, the more waterproof it is.
Here are the waterproofing ratings:
Component resistant to water pressure of 5,000 mm after ageing (5 washes). This equates to 5,000 Schmerber - average pressure exerted by the water during rain.
The hat's waterproof was tested in a rain shower with 100 litres of water / sqm / hour for 3 hours.
Here are the waterproofing ratings:
Component resistant to water pressure of 5,000 mm after ageing (5 washes). This equates to 5,000 Schmerber - average pressure exerted by the water during rain.
The hat's waterproof was tested in a rain shower with 100 litres of water / sqm / hour for 3 hours.
Waterproofing 2/2
Waterproof components (water runs off the fabric)
- 100% waterproof seams
- 100% waterproof seams
Fabric breathability
To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric's resistance, the more moisture is evaporated, and therefore the higher the fabric's breathability.
We consider that if:
RET < 9 = very breathable fabric
9 < RET < 12 = breathable fabric.
The values for the Trek 500 jacket’s breathability are as follows:
> More resistant fabric: RET < 12 (or 3621 g/m²/24 h, JIS1099A standard)
> Lightest fabric: RET < 8 (or 2972 g/m² /2
We consider that if:
RET < 9 = very breathable fabric
9 < RET < 12 = breathable fabric.
The values for the Trek 500 jacket’s breathability are as follows:
> More resistant fabric: RET < 12 (or 3621 g/m²/24 h, JIS1099A standard)
> Lightest fabric: RET < 8 (or 2972 g/m² /2
Water-repellent properties information
A fabric is water-repellent when water slides off the surface of the fabric, without seeping in.
Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered.
The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.
Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered.
The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.
HOW TO REACTIVATE THE WATER REPELLENCY:
Drying is a crucial phase in reactivating the water repellent treatment.
We recommend that you lay your anorak flat on a clothes rack and leave it out to dry in the open. Caution: never dry your anorak directly on a radiator.
Then place it in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.
We recommend that you lay your anorak flat on a clothes rack and leave it out to dry in the open. Caution: never dry your anorak directly on a radiator.
Then place it in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.
composition
composition
Main fabric: 100.0% Polyester; Membrane: 100.0% Polyurethane; Inner fabric: 12.0% Elastane, 88.0% Polyester
Tips for storage and maintenance
ANY TYPE OF IRONING ALLOWED.
MAXIMUM WASH TEMPERATURE OF 30°C. VERY MODERATE TREATMENT.
IRON AT A MAXIMUM SOLEPLATE TEMPERATURE OF 150°C.
MAXIMUM WASH TEMPERATURE 70°C. NORMAL TREATMENT.
IRONING AT A MAXIMUM IRON SOLEPLATE TEMPERATURE OF 200°C.
TESTS AND WARRANTY
Warranty
2 Years