ITIWIT
Ref.
8666669
4363527
Surfing inflatable SUP minimalibu 500 / 9" 120L
€470.00
Tax included
Store Availability
Store Availability
Take on the waves with this compact 9-foot surfing SUP: Ideal for advanced wave-riders weighing less than 65 kg and for waves up to 1.5 metres high.
BENEFITS
Compact design
Dimensions folded in the bag 90 x 35 x 20 cmEasy assembly / dismantling
Inflates to 17 psi in 3 minutes (120 litres)Easy transport
7.6 kg board and backpack with padded strapsGlide performance
Semi-rigid square rail to improve the flow and grip in the wavesRigidity
2 polyethylene & reinforced woven dropstitch stringers for extra rigidityEase of handling
The size of this surf SUP makes it the easiest to handle in the range: 9' x 28''TECHNICAL INFORMATIONS
Recommended user weight
Recommended user weight:
Less than 50 kg: the ideal board for easily getting into SUP surfing
Between 50 and 65 kg: board suitable for intermediate SUP surfers
Over 65 kg: board for advanced users only
Maximum load to stay above the water: 95 kg.
Less than 50 kg: the ideal board for easily getting into SUP surfing
Between 50 and 65 kg: board suitable for intermediate SUP surfers
Over 65 kg: board for advanced users only
Maximum load to stay above the water: 95 kg.
Inflated shape and dimensions
ITIWIT's SURF SUP 9' is a MINI MALIBU board: with a round nose and round pintail, it is similar to a longboard, only smaller!
Ideal for surfers who like to carve smooth curves in the waves.
Length: 9' (274 cm)
Width: 28" (71 cm)
Thickness: 3" (7.5 cm)
Volume: 120 litres
Board weight: 7.6 kg
Ideal for surfers who like to carve smooth curves in the waves.
Length: 9' (274 cm)
Width: 28" (71 cm)
Thickness: 3" (7.5 cm)
Volume: 120 litres
Board weight: 7.6 kg
Inflating & deflating the stand-up paddleboard
INFLATION
This SUP is equipped with a NEW GENERATION valve for even greater security.
To inflate your SUP, open the cover and connect the pump (“IN” mode).
Inflate to 17 psi for best results.
Disconnect the pump and close the exterior cover
DEFLATING
Turn the cover a quarter clockwise (“out” mode).
Roll up starting from the side opposite to the valve to remove all the air to completely fold
Close the cap
This SUP is equipped with a NEW GENERATION valve for even greater security.
To inflate your SUP, open the cover and connect the pump (“IN” mode).
Inflate to 17 psi for best results.
Disconnect the pump and close the exterior cover
DEFLATING
Turn the cover a quarter clockwise (“out” mode).
Roll up starting from the side opposite to the valve to remove all the air to completely fold
Close the cap
Installing and removing the fin
This surf SUP has a "SINGLE FIN" set-up. This means it has one fin (ref: 8576512) installed on the centre line of the board. We chose this type of set-up for better HANDLING of the surf SUP in the waves
NB: Remember to remove the fins once you get out of the water.
If possible, rinse the fin base before and after use.
NB: Remember to remove the fins once you get out of the water.
If possible, rinse the fin base before and after use.
Carry bag
Two-tone fabric bag (see ''SUSTAINABLE DEVELOPMENT ADDITIONAL INFORMATION'' section to find out more)
Height: 90 cm
Width: 35 cm
Thickness: 20 cm
approx. 63 L
These dimensions leave room for a pump and paddle.
Interior pocket and compression system included
Height: 90 cm
Width: 35 cm
Thickness: 20 cm
approx. 63 L
These dimensions leave room for a pump and paddle.
Interior pocket and compression system included
LEASH
Always wear your leash to stay attached to your board if you fall. It’s best to attach it to your ankle, but it can also be attached to the knee.
Remove it and rinse after each use.
PLEASE NOTE: do not use a leash on rivers
Remove it and rinse after each use.
PLEASE NOTE: do not use a leash on rivers
Folding the board
Empty all the air from the board
Start folding up from the fin base, following the dotted lines to avoid damaging the base.
Stop halfway and start a second folding beginning from the valve side (wallet folding).
Start folding up from the fin base, following the dotted lines to avoid damaging the base.
Stop halfway and start a second folding beginning from the valve side (wallet folding).
OUR BOARDS CAN BE REPAIRED!
The vast majority of surfing stand up paddleboards are repairable:
For small repairs, we sell a stand-up paddle board repair kit, reference 8512384.
For more complex repairs: we recommend contacting the workshop at your nearest store: valve, handle, fin box... our workshops can repair them all to prolong the life of your surf SUP
For small repairs, we sell a stand-up paddle board repair kit, reference 8512384.
For more complex repairs: we recommend contacting the workshop at your nearest store: valve, handle, fin box... our workshops can repair them all to prolong the life of your surf SUP
How to take off on a surf SUP
When a wave is approaching, position both of your feet on the white areas in the middle of the "dots" arranged symmetrically around the handle.
Start paddling and do not stop until you feel the wave lift you up.
Once you feel the wave pushing you along: move your back foot onto the orange area (right foot for REGULAR stance, left foot for GOOFY stance).
Ideally, your back foot should be on the foam arch in the orange area and your front foot in front of the handle
Start paddling and do not stop until you feel the wave lift you up.
Once you feel the wave pushing you along: move your back foot onto the orange area (right foot for REGULAR stance, left foot for GOOFY stance).
Ideally, your back foot should be on the foam arch in the orange area and your front foot in front of the handle
composition
composition
Main fabric: 70.0% Polyvinyl Chloride, 30.0% Polyester; Carry bag: 100.0% Polyester; Foam: 25.0% Ethylene Vinyl Acetate, 75.0% Polyethylene
Tips for storage and maintenance
Storage tips
Store deflated, flat and out of sunlight, after first removing the fin and leash. If storing inflated, release some of the pressure and store in a flat position without any load
TESTS AND WARRANTY
Warranty
2 Years
Parts guarantee
Warranty: 2 years