Women's Windproof Waterproof Jacket SAILING 300 light khaki

Component Breathability

To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric's resistance, the more moisture is evaporated, and therefore the higher the fabric's breathability.

We consider that if:

RET < 9 = very breathable fabric

9 < RET < 12 = breathable fabric.

The Sailing 300 vest’s RET is 12.

Front zip closure

Using a zip on the entire jacket length with an interior channel (flap) that protects against the wind and water. The outer flap prevents water from entering through the zip and ensures a higher level of waterproofing.

Soft fabric flap on the top of the collar to protect the chin.

Hood

The hood can be stored in the collar. The collar is then closed by an injected plastic zip to avoid salt oxidation.

Completely depth and height-adjustable hood: adjustment at the back of the hood and around the neck

Visor with headband for better fit and to protect the face from rain.

The chin-high neck effectively protects the lower part of the face.

How to reactivate the anorak's water repellency

Drying is a crucial phase in reactivating the water repellent treatment.

We recommend that you lay your anorak flat on a clothes rack and leave it out to dry in the open. Caution: never dry your anorak directly on a radiator.

Then place it in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.

How to wash your jacket?

To maintain the water repellent properties, infrequent washing is recommended.

Close all zips and flaps, empty all pockets and then turn the garment inside out to wash it. You can wash it on a synthetic cycle at 30°C or 40°C with your usual detergent. Do not use fabric conditioner, which could damage the existing performance of the garment, or bleach. Very important: choose a full-rinse cycle or extra rinse.

Pockets

2 pockets on the front of the jacket, for your VHF, sail tie, cap, etc. Injection-moulded plastic zip to avoid salt oxidation

1 interior pocket on the right of the chest to store your phone or other items, closed with a zip

WARNING: the pockets are NOT WATERPROOF

Sleeves

At the end of the sleeve there is an adjustable sleeve with a rip-tab. It lets you adjust the sleeve to your arm length, but also stops air and water coming in.

To easily remove the jacket, open the sleeves

Waterproofing 1/2

We measure the resistance of a fabric to water pressure in mm of water column (based on the ISO 811 standard). The higher the water pressure withstood by the fabric, the more waterproof it is.

Here are the waterproofing ratings:

Component resistant to water pressure of 15,000 mm after ageing (5 washes). This equates to 15 000 Schmerber - average pressure exerted by the water during rain.

The jacket's waterproofing has been tested in a rain shower with 60 litres of water / m² / hour for 2 hours

Waterproofing 2/2 - Technical features of the jacket 300

- Water-repellent coated fabric (water runs off the fabric)

- 100% waterproof seams

- Adjustable jacket bottom with elasticated cord

- Sleeve ends adjustable at the wrist with rip-tab strips.

- Zip fastening protected by internal and external zip flaps.

- Collar height (back) of 11.5 cm

- Injection-moulded plastic zip to avoid salt oxidation

Water-repellent properties information

A fabric is water-repellent when water slides off the surface of the fabric, without seeping in.

Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered.

The water-repellent properties can be reactivated by putting the anorak in a dryer for 10 minutes at the lowest temperature.