Men’s Sailing jacket Offshore 900 - Red
This jacket is designed for offshore sailing to protect you from spray, wind and waves Waterproof in torrential rain for 24 hours
This sailing jacket for offshore sailing has excellent waterproofing, reinforcements, a high collar and double cuffs.
Waterproof in stormy rain for 24 hours
BENEFITS
Water repellent
Water pearls and streams off the fabric to keep you dry
Resistance to salt water
Water-repellent YKK AquaGuard® zips
Adjustable
Rip-tab double cuffs, waist skirt, fully adjustable hood
Robustness
Reinforced sleeves and jacket hem for durability
Waterproof
100% taped seams 3-layer membrane 30,000 mm Schmerber
Pockets
5 pockets: 2 hand-warmers, 2 cargo pockets, and one secure pocket under the flap
Breathability
3-layer breathable membrane, RET = 25, MVP 2000 g/m²/24 h
TECHNICAL INFORMATIONS
What’s the difference between a shell jacket and a sailing jacket?
The shell jacket has been adapted for manoeuvres at the bow of a boat (positions 1 and 2), and allows for increased protection in extreme weather conditions, thanks to its half-zip.
Nevertheless, the jacket is rather advised for less exposed positions, and its zip allows for the jacket to be entirely opened, easily and quickly.
How to wash your jacket
After use, rinse the jacket thoroughly with clean water to remove any salt. Machine wash about once a year to prevent the rip-tabs from damaging the fabric during washing.
Dry in a well-ventilated place. Caution: never dry your jacket directly on a radiator.
If the water repellency is less effective, you can occasionally tumble dry it at low temperature for 10 minutes to reactivate the water repellency.
How to choose the size of your jacket
The product sizing is generously cut. It is designed to be worn with thermal underlayers and a fleece underneath.
Choose your usual size.
Pockets
The jacket has 5 pockets:
- 2 hand-warmer pockets, under the chest and sealed with YKK AquaGuard® zips
- 2 cargo pockets at the waist
- 1 secure pocket under the flap with a YKK AquaGuard® zip
Pockets have a drainage system to allow for water evacuation.
Double sleeve seals
Double sleeve seals:
- An adjustable neoprene section inserted into a soft, comfortable fabric on the inside of the sleeve seal to provide extra protection from incoming water in bad weather.
- An external sleeve seal in a waterproof material, which can be adjusted with rip-tab to protect the neoprene and provide optimal waterproofing.
Tips: if you wear mitts or gloves, wear them between the 2 sleeve seals for extra comfort and to avoid water getting in through any gaps or creases.
Jacket waterproofing
- The neoprene sleeve seals covered with extra fabric limit water getting in.
- The seams are 100% watertight.
- A rigid visor has been integrated into the hood for greater protection.
- A wave guard/windbreaker layer inside the jacket. Fastenings with press studs. This fastening avoids water sprays getting into the jacket and dungarees.
The water resistance level
The fabric is constructed with a 3-layer membrane, resistant to a water pressure of 30,000 mm Schmerber (JIS standard). The higher the water pressure withstood by the fabric, the more waterproof it is.
The product has been tested using a rainstorm simulator, reproducing rainfall of 450 L/M²/h over 24 hours (3x8 hours)
Breathability
To find out whether a fabric is breathable, we measure its evaporative resistance, or RET, (test based on the ISO 11092 standard). It is its ability to allow the water vapour produced by the body during exercise to escape.
To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric’s resistance, the more moisture is evaporated, and therefore the higher the fabric’s breathability.
This product’s RET is 25.
Developed and validated by ocean racers.
The Tribord Offshore 900 ranges have been developed and tested with navigators during a transatlantic race, as well as solitary offshore races, and on various boats: Jean-Baptiste Daramy on Class 40, Achille Nebout on Figaro 3, Romain Le Gall and Léo Bothorel on Mini 6.50.
How to reactivate the water repellency
Drying is a crucial phase in reactivating the water repellent treatment.
We recommend that you lay your jacket flat on a clothes rack and leave it out to dry in the open. Caution: never dry your anorak directly on a radiator or in direct sunlight.
Then place them in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.
Abrasion resistance
The jacket has reinforcements level with the buttocks, for increased resistance against abrasion.
What is water repellency and how to maintain it
The fabric and fastenings are water-repellent.
A fabric is water-repellent when water slides off the surface without seeping in.
It won’t become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment (DWR) applied to the external side of the fabric, but these properties can be altered.
The water-repellent properties can be reactivated by putting the jacket (once it has been air-dried) in a dryer for 10 minutes at the lowest temperature.
Weight
The jacket weighs 1175 grams in Size L
composition
composition
Main fabric: 100.0% Polyamide; Underarm fabric: 100.0% Polyester; Hood fabric: 100.0% Polyester; Membrane: 100.0% Polyurethane; Back fabric: 100.0% Polyester; Wristband: 4.0% Elastane, 6.0% Polyamide, 90.0% Rubber; Warm lining: 100.0% Polyester
Tips for storage and maintenance
Storage tips
Store in a dry, well-ventilated place, but do not leave your garment on a heat source such as a radiator, as this may damage the breathable membrane.
TESTS AND WARRANTY
Warranty
2 Years
Agree by
Achille Nebout (Figaro 3), Romain Le Gall and Léo Bothorel (Mini 6.50)