Men's Waterproof and Wind-proof Sailing Jacket SAILING 500 black

Fabric breathability

To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric's resistance, the more moisture is evaporated, and therefore the higher the fabric's breathability.

We consider that if:

RET < 9 = very breathable fabric

9 < RET < 12 = breathable fabric.

The Sailing 500 vest’s RET is below 12.

Front zip closure

Using a YKK zip on the entire anorak length with an interior flap that protects against the wind and water.

Two-way zip lets you open the anorak by the arms. For two-way zip at the front to work properly, make sure both sides are aligned.

Soft fabric flap on the top of the collar to protect the chin.

Hood

The hood does not pack down into the collar, it is attached. Its weight stops it from flapping in the wind.

Completely depth and height-adjustable hood.

Visor with a headband to provide a high level of protection and better maintenance.

The high neck effectively protects the lower part of the face.

How to reactivate the anorak's water repellency

Drying is a crucial phase in reactivating the water repellent treatment.

We recommend that you lay your anorak flat on a clothes rack and leave it out to dry in the open. Caution: never dry your anorak directly on a radiator.

Then place it in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.

How to wash your jacket?

To maintain the water repellent properties, infrequent washing is recommended.

Close all zips and flaps, empty all pockets and then turn the garment inside out to wash it. You can wash it on a synthetic cycle at 30°C or 40°C with your usual detergent. Do not use fabric conditioner, which could damage the existing performance of the garment, or bleach. Very important: choose a full-rinse cycle or extra rinse.

Pockets

Two pockets accessible behind the cargo pockets, with a zip.

Two cargo pockets at the bottom of the anorak for your VHF radio, sail ties and cap. There is a small inner pouch in the right-hand pocket for knives or shackles keys.

One exterior pocket on the right side of the chest to store your phone or other items closed with a zip

One inside pocket on the right side of the chest to store your phone or other items closed with a zip

WARNING: the pockets are NOT WATERPROOF

Protection - sleeves

Two cuffs per arm covering the wrist that are adjustable with a rip-tab to limit water ingress.

The first cuff is in a smooth and comfortable component to stop water ingress and so that it is comfortable against the skin. Adjustment with rip-tab.

The second cuff can be put on over a glove.

To easily remove the anorak, open the cuffs fully

Waterproofing 1/2

We measure the resistance of a fabric to water pressure in mm of water column (based on the ISO 811 standard). The higher the water pressure withstood by the fabric, the more waterproof it is.

Here are the waterproofing ratings:

Component can resist water pressure of up to 12,000mm Schmerber. This equates to the average pressure applied by the water during a rain shower.

The anorak's waterproof was tested in a rain shower with 100 litres of water / m² / hour for 3 hours.

Waterproofing 2/2

High collar lined with a fleece

- Injection-moulded plastic zip to avoid salt oxidation

- Water-repellent components (water runs off the fabric).

- 100% taped seams.

- Central opening features a flap with a drainage channel for optimal waterproofing

Water-repellent properties information

A fabric is water-repellent when water slides off the surface of the fabric, without seeping in.

Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered.

The water-repellent properties can be reactivated by putting the anorak in a dryer for 10 minutes at the lowest temperature.