Men's diving semi-dry wetsuit 7 mm neoprene blue grey
Store Availability
Store Availability
BENEFITS
Easy dressing
One-piece with separate hood. Zips on the ankles and wrists.
Thermal insulation
7 mm neoprene semi-dry suit. Neoprene thermospan on the chest and plush.
Freedom of movement
Pre-shaped cut on the arms and legs, arch for easier movements.
Robustness
Printed reinforcements on the knees (Supratex) and print on the shoulders.
Waterproof
Double smooth and zipped cuffs (when turned up). T-ZIP watertight back zip.
Instructions
DownloadTECHNICAL INFORMATIONS
Details of thermal insulation
The suit is made from 7mm stretch neoprene panels (with production tolerance).
Distribution:
Thermospan on the chest and back + Plush (nylon loops) on the shoulders to increase the feeling of warmth
Supratex on the knees for increased resistance to friction
Stretch over the rest of the diving suit
Smooth Glideskin cuffs at the ends of the sleeves and on the neck: the smooth part is to ensure it sticks to the skin and limits the inflow and circulation of water.
Watertight zip and diving suit assembly
The Tizip back zip is fully watertight. You are advised to lubricate regularly with silicone grease to lengthen the zip’s lifespan and to make the diving suit easier to close. The seams of the suit and hood are waterproof, with a glued and blind stitched (GBS) assembly: the neoprene is glued first of all, then sewn for maximum strength (the sewing needle does not go completely through the neoprene in order to prevent water infiltration).
Freedom of movement
One-piece with separate hood. Stretch neoprene side panels (very soft and stretchy neoprene) to adapt to fit different body shapes and suit various physiques.
No underarm seams for easier arm movements. Pre-shaped cut on the arms and legs, with back arch for easier movements.
Hood
A separate 7 mm thick neoprene hood, with plush loop interior, that fits flat against the face with a preformed chin. The central grey band is made of stretch neoprene to best adapt to the shape of the head.
Air Expulse system: a system to evacuate air bubbles trapped in the hood. It features a snap hook to attach it to the right thigh of the suit.
Getting the suit on and off
Double cuffs with zips on the arms and legs for maximum comfort when putting on. The elongated pull cord makes it easier to close the back zip.
Reinforcements to reduce wear
Ergonomic reinforcements on the knees (Supratex) and reinforcement panels on the shoulders. These reinforcements limit the effects of friction related to the material. The interior seams are ended with patches to make them stronger. The GBS seams are made of nylon thread rather than polyester for greater resistance to wear. Grippy print at the wrist to prevent the dive computer from turning.
Thermal performance class
This scuba diving suit provides thermal protection that has been tested by the independent INPP institute (Marseille, France) in order to validate its compliance with the current standard (EN 14225-1:2017).
CLASS B certified diving suit.
A (+7 °C/+12 °C/+45 °F/+54 °F)
B (+10 °C/+18 °C/+50 °F/+64 °F)
C (+16 °C/+24 °C/+61 °F/+75 °F)
D (+22 °C/+30 °C/+72 °F/+86 °F).
What is a semi-dry suit?
The semi-dry suit works on the same principle as a diving suit, except that the TiZIP concept back zip is watertight. The cuffs prevent water from circulating. They are in fact clothes with low water circulation! The water is not renewed, which means there is less energy loss. Even if the body is wet, the main advantage of this diving suit is that is keeps you warm when diving.
How to use a semi-dry suit
Put a little lukewarm water (with the aid of a Thermos flask) into your semi-dry suit before diving. This will reduce the squeeze effect: under the effects of pressure during the descent, air trapped in the suit from when it was put on gets compressed and can crush the neoprene, creating folds and leading to pinching of the skin. Remember to regularly lubricate the waterproof zip with a non-fatty silicone lubricant.
Tips on how to get into a diving suit
Put your foot in a plastic bag. Then, slip your foot into your diving suit. Your entire foot comes out without snagging! To adjust, ask someone to blow into your sleeve from the wrist. The incoming air inflates the interior of the neoprene diving suit, immediately separating it from your skin. You can then easily proceed with the final adjustments.
Tips on how to take care of your diving suit
1) Soak the inside and the outside of the diving suit in clean water after each session.
2) Clean with a bactericide solution.
3) Rinse thoroughly in clean water.
4) Dry on a wide hanger in a dark and well-ventilated place. Caution: the sun will cause the colours of the textile parts of the diving suit to fade and speeds up the ageing process of the neoprene.
Zips can be cleaned with a toothbrush and lubricated with silicone grease.
composition
composition
Foam: 100.0% Rubber; Lining: 100.0% Polyamide
Tips for storage and maintenance
HAND WASH. MAXIMUM TEMPERATURE OF 40°C.
BLEACHING EXCLUDED.
DO NOT TUMBLE DRY.
DO NOT IRON.
DO NOT DRY CLEAN.
Storage tips
Lay your diving wetsuit out away from sunlight and away from a heat source on a wide hanger, to keep its shape and to preserve its neoprene.
Restrictions on use
Regularly apply non-greasy silicone lubricant.
TESTS AND WARRANTY
Test product
Designed and tested by our teams and our technical partner in Hendaye (France) to approve the thermal insulation.
Warranty
2 Years
Agree by
Our technical partner: Planet Ocean (the PADI 5-star diving centre) based on the Water Sports Centre by DECATHLON in Hendaye - France. The centre uses SUBEA equipment throughout the year. The team of instructors are rigorously involved in the development of our SUBEA diving products: from the design phase with the SUBEA team (product manager, designers and engineers), to the endurance tests with the help of the centre’s divers (from beginners to trainee instructors, all year round).
Videos
Our Ecodesign Approach
Our ecodesign approach reduces the environmental impact of our products.
We’ve examined the environmental footprint of this product in order to identify how we can produce it in a more sustainable way. With this knowledge, our design teams were able to develop this product while significantly reducing its environmental impact.
Sustainable design measures implemented on this product.
-
Long lastingReparability
Product designed to be repairable on more than 80% of breakages and failures.
Repairability is the ability to offer a solution in the event of product breakage or failure. The repairability of a product is defined according to 4 criteria: - the availability of instructions on how to repair the product for customers, - the possibility of disassembling the product, - the availability of spare parts, - the price of the repair is lower than purchasing a new product. Our goal is to cover any possible known break or repair possibility a product might have. We think about the life span of a product from the design stage, to ensure that it lasts as long as possible.