TRIBORD Ref. 8675975 4450034

Women's sailing waterproof jacket - Wet-weather jacket SAILING 100 navy blue

€30.00
Tax included
PRICE DROP
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
  • Women’s waterproof sailing jacket - wet-weather jacket SAILING 100 ochre
Colour: BLUE
  • BLUE
  • PINK / COLORLESS
  • WHITE / BLUE / ORANGE
  • PURPLE
  • BLUE
  • WHITE
  • YELLOW
Size guide My size is :

Size guide

Not available

Store Availability

Store Availability

Close
Our designers—and fellow sailors—developed this inshore sailing anorak for sailing in warm and stormy weather.

BENEFITS

Compact design

Compact, the jacket folds away into its hood

Water repellent

Especially treated so water slides off the fabric surface.

Water resistance

Materials and zips resistant to salt water and sea air.

Windproof

Fabric especially coated to reduce the cooling effect of the wind.

Waterproof

Moderate rain for 2 hrs 5,000 mm Schmerber (JIS standard) Pockets not waterproof

Pockets

3 secure pockets, including 1 inner pocket

Breathability

Very breathable coated fabric (RET < 12): reduces condensation

TECHNICAL INFORMATIONS

Waterproofing 1/2

We measure the resistance of a fabric to water pressure in mm of water column (based on ISO 811 ). The higher the water pressure withstood by the fabric, the more waterproof it is.

Here are the waterproofing ratings:

Component resistant to water pressure of 5,000 mm before and after ageing (5 washes). This equates to 5,000 Schmerber - average pressure exerted by the water during rain.

The anorak's waterproofness was tested in a rain shower with 60 litres of water/m²/hour for 2 hours.

Waterproofing 2/2

- High collar

- Injection-moulded plastic to avoid salt oxidation

- Water-repellent components (water runs off the fabric)

- 100% taped seams

- Central opening features a flap with a drainage channel for optimal waterproofing

Hood

The hood does not pack down into the collar, it is attached.

Completely depth and height-adjustable hood.

Visor with a headband to provide a good level of protection and a better hold.

The high neck effectively protects the neck.

pockets

2 zip pockets on the front of the jacket to put your hands or some items

1 inside pocket on the right side of the chest with a rip-tab closing

NOTE: the pockets are NOT WATERPROOF

Front zip closure

A zip on the entire jacket length with an interior flap protects against the wind and water.

Soft fabric flap on the top of the collar to protect the chin.

Fabric breathability

To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric's resistance, the more moisture is evaporated, and therefore the higher the fabric's breathability.

We consider that if:

RET < 9 = very breathable fabric

9 < RET < 12 = breathable fabric.

The values for the Trek 500 jacket’s breathability are as follows:

> More resistant fabric: RET < 12 (or 3621 g/m²/24 h, JIS1099A standard)

> Lightest fabric: RET < 8 (or 2972 g/m² /2

Water-repellent properties information

A fabric is water-repellent when water slides off the surface of the fabric, without seeping in.

Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered.

The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.

How to wash your jacket?

To maintain the water repellent properties, infrequent washing is recommended.

Close all zips and flaps, empty all pockets and then turn the garment inside out to wash it. You can wash it on a synthetic cycle at 30°C or 40°C with your usual detergent. Do not use fabric conditioner, which could damage the existing performance of the garment, or bleach.

Very important: choose a full rinse cycle or extra rinse.

How to reactivate the jacket's water repellency

Drying is a crucial phase in reactivating the water repellent treatment.

We recommend that you lay your jacket flat on a clothes rack and leave it out to dry in the open. Caution: never dry your jacket directly on a radiator.

Then place them in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.

composition

composition

Lower part - Main fabric: 100.0% Polyamide; Upper part - Main fabric: 100.0% Polyamide; Main lining: 100.0% Silicone; Sleeve lining: 100.0% Silicone; Coating: 100.0% Polyurethane

Tips for storage and maintenance

MAXIMUM WASHING TEMPERATURE 30°C. NORMAL TREATMENT.

MAXIMUM WASHING TEMPERATURE 30°C. NORMAL TREATMENT.

BLEACHING EXCLUDED.

BLEACHING EXCLUDED.

DRYING IN TUMBLE DRYER POSSIBLE. LOW TEMPERATURE, MAXIMUM DRUM EXHAUST TEMPERATURE 60°C.

DRYING IN TUMBLE DRYER POSSIBLE. LOW TEMPERATURE, MAXIMUM DRUM EXHAUST TEMPERATURE 60°C.

DO NOT IRON.

DO NOT IRON.

DO NOT DRY CLEAN.

DO NOT DRY CLEAN.

TESTS AND WARRANTY

Warranty

2 Years

Our Ecodesign Approach

Our ecodesign approach reduces the environmental impact of our products.

We’ve examined the environmental footprint of this product in order to identify how we can produce it in a more sustainable way. With this knowledge, our design teams were able to develop this product while significantly reducing its environmental impact.

Sustainable design measures implemented on this product.
  • Picture showing Dope dyed
    Process

    Dope dyed

    Product made from 51% dope dyed yarn

    Using this mass-dyeing process enables us to reduce CO2 emissions linked to the production of dyed textiles by at least 17% compared to conventional dyeing.

  • Picture showing Recycled polyester
    Material

    Recycled polyester

    Product made from 21% recycled polyester

    Using recycled polyester rather than conventional polyester reduces the CO2 emissions linked to the material by at least 17%.

 Learn more about our sustainable approach to product design