Men’s sailing waterproof windproof jacket - Sailing 500 grey yellow hood
Store Availability
This jacket is designed for inshore sailing in wet, cool and windy conditions. Waterproof in moderate rain for 2 hours.
This waterproof and breathable sailing jacket with a fleece-lined collar is lightweight and easy to adjust for optimal comfort during all your outings
Withstands moderate rain for 2 hours
BENEFITS
Water repellent
Water beads and runs off the fabric to keep you dry for longer
Windproof
Windproof membrane, high neck, and adjustable hood with good coverage
Waterproof
100% taped seams 2-layer membrane 15,000 mm Schmerber
Pockets
4 pockets: 2 zipped fleece-lined, 1 chest zipped, 1 inside with rip-tab
Breathability
Breathable 2-layer membrane, RET 12 for moderate exertion
TECHNICAL INFORMATIONS
How to wash your jacket?
To maintain the water repellent properties, infrequent washing is recommended.
Close all zips and flaps, stow the hood and then turn the garment inside out to wash it. You can wash it on a synthetic cycle at 30°C or 40°C with your usual detergent. Do not use fabric conditioner, which could damage the existing performance of the garment, or bleach. Very important: choose a full rinse cycle or extra rinse.
Waterproofing - the jacket’s component
We measure a fabric’s resistance to water pressure in mm of water column (JIS standard). The higher the water pressure withstood by the fabric, the more waterproof it is.
Here are the waterproofing ratings:
Component resistant to water pressure of 5,000 mm after ageing (5 washes). Equates to 15,000 Schmerber (JIS standard), which is the average pressure applied by the water in a shower.
The anorak’s waterproofness was tested in a rain shower with 60 litres of water/m²/hour for 2 hours.
The jacket’s uniqueness
Compared with our sailing 100 jacket, the jacket:
- more waterproof (15,000 Schmerbers) and stretchy fabric
- rip-tab wrist fastening
- inner under flap with a drainage channel
- hood that stows in the collar and can be adjusted in depth
- additional outside breast pocket
Water-repellent properties information
A fabric is water-repellent when water slides off the surface of the fabric, without seeping in.
Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered.
The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.
Pockets
2 pockets on the front of the jacket, for your VHF, sail tie, cap, etc. Injection-moulded plastic zip to prevent salt oxidation
1 inside chest pocket on the left side to store your phone or other items, fastened with a zip
1 inside chest pocket on the right side fastened by hook and loop
PLEASE NOTE: the pockets are NOT WATERPROOF
Technical features of the component
Laminated fabric. Waterproof fabric: 15,000 Schmerbers
- Water-repellent fabric (water runs off the fabric)
- 100% taped seams
Collar and hood
The hood can be stored in the collar. The collar is then fastened with plastic press studs to prevent oxidation by salt.
Completely depth and height-adjustable hood: adjustable at the back of hood and on the collar.
The chin-high neck effectively protects the lower part of your face. 9 cm high collar (at the back)
Component Breathability
To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric’s resistance, the more moisture is evaporated, and therefore the higher the fabric’s breathability.
We consider that if:
RET < 9 = very breathable fabric
9 < RET < 12 = breathable fabric.
The RET of the Sailing jacket is 12.
How to reactivate the jacket’s water repellency
Drying is a crucial phase in reactivating the water repellent treatment.
We recommend that you lay your jacket flat on a clothes rack and leave it out to dry in the open. Caution: never dry your jacket directly on a radiator.
Then place them in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.
Sleeve protection
The end of the sleeve is adjustable with a rip-tab. It lets you adjust the sleeve to your arm length, but also stops air and water coming in.
To take off the jacket more easily, fully open the rip-tab
Front zip closure
The zip along the entire length is protected by an internal flap with a drainage channel for better waterproofing.
Soft fabric flap at the top of the collar to limit chin irritation.
Injected plastic zip to prevent oxidation by salt
composition
composition
Main fabric: 100.0% Polyester; Main lining: 100.0% Polyester; Secondary lining: 100.0% Polyester; Coating: 100.0% Polyurethane
TESTS AND WARRANTY
Warranty
2 Years
Our Ecodesign Approach
Our ecodesign approach reduces the environmental impact of our products.
We’ve examined the environmental footprint of this product in order to identify how we can produce it in a more sustainable way. With this knowledge, our design teams were able to develop this product while significantly reducing its environmental impact.
Sustainable design measures implemented on this product.
-
MaterialRecycled polyester
Product made from 69% recycled polyester
Using recycled polyester rather than conventional polyester reduces the CO2 emissions linked to the material by at least 17%.
-
ProcessDope dyed
Product made from 11% dope dyed yarn
Using this mass-dyeing process enables us to reduce CO2 emissions linked to the production of dyed textiles by at least 17% compared to conventional dyeing.